介孔分子硅剂改善茶浓缩膜结构特性应用研究

为有效提高功能性茶浓缩反渗透膜的回收效率和抗污性能,探究了3种介孔分子硅材料(MCM-41、SBA-15和MCFs)对浓缩膜面聚酰胺层聚合形成过程的结构影响。结果表明,添加质量分数0.02%经磺化预处理的MCM-41于间苯二胺水相可接枝酰氯基团,形成的聚酰胺结构层峰谷粗糙跨度仅为220 nm且交联紧致,膜抗拉伸强度增加37.8%;SBA-15和MCFs相膜面峰谷跨度达500~780 nm,横向褶皱和团聚,结构存在孔道塌陷;改性膜在3 h内对茶多酚、茶多糖、茶蛋白即可达到最大浓缩度,减少50%浓缩时间;MCM-41和SBA-15膜长时间运行的浓缩降率仅为2.8%~6.1%,48 h下降率比显示改性膜达标使用时长增加112.5%~137.5%,亲水性和抗污堵能力均大幅提升,可有效满足功能化茶浓缩精度。     

用于水质净化的氧化石墨烯膜研究进展

氧化石墨烯膜具有超高的水通量、可控的层间距以及卓越的分离性能，这些优异的特性使氧化石墨烯膜有望成为新一代膜材料并用于水环境中物质的精确分离。对氧化石墨烯膜的研究已经取得了许多重要的成果，本文系统地阐述了用于水质净化的氧化石墨烯膜的结构特性和构效关系，总结了氧化石墨烯膜典型的制备方法，重点介绍了氧化石墨烯膜的改性方式，概述了氧化石墨烯膜在多种水环境中的应用，总结并展望了氧化石墨烯膜的发展方向，为设计和合成高性能氧化石墨烯膜用于水质净化提供新的思路。     

Impact of adhesive ingredients on adhesion between rubber and brass-plated steel wire in tire

Proficiency on underlying mechanism of rubber-metal adhesion has been increased significantly in the last few decades. Researchers have investigated the effect of various ingredients, such as hexamethoxymethyl melamine, resorcinol, cobalt stearate, and silica, on rubber-metal interface. The role of each ingredient on rubber-metal interfacial adhesion is still a subject of scrutiny. In this article, a typical belt skim compound of truck radial tire is selected and the effect of each adhesive ingredient on adhesion strength is explored. Out of these ingredients, the effect of cobalt stearate is found noteworthy. It has improved adhesion strength by 12% (without aging) and by 11% (humid-aged), respectively, over control compound. For detailed understanding of the effect of cobalt stearate on adhesion, scanning electron microscopy and energy dispersive spectroscopy are utilized to ascertain the rubber coverage and distribution of elements. X-ray photoelectron spectroscopy results helped us to understand the impact of Cu_XS layer depth on rubber-metal adhesion. The depth profile of the Cu_XS layer was found to be one of the dominant factors of rubber-metal adhesion retention. Thus, this study has made an attempt to find the impact of different adhesive ingredients on the formation of Cu_XS layer depth at rubber-metal interface and establish a correlation with adhesion strength simultaneously.     

Deposition-environment-dependent structural and magnetic property modification of [111]-oriented epitaxial CoFe2O4 films

We examined the magnetic, structural, and chemical properties of CoFe₂O₄ films deposited on Al₂O₃ substrates using RF-magnetron sputtering under Ar and Ar + O₂ environments. Perpendicular magnetic anisotropy with large magnetization was observed in the case of the film deposited under the Ar + O₂ environment. However, no significant anisotropy appeared in the film deposited under the Ar environment. Interestingly, depth-dependent X-ray photoelectron spectra showed nearly identical stoichiometric ratios of Co/Fe and oxygen vacancies regardless of the deposition environment. Structurally, high-quality crystallinity with in-plane compressive strain, and lower surface and interfacial roughness were induced in the film deposited under the Ar + O₂ environment. Cross-sectional transmission electron microscopy and X-ray reflectivity measurements showed that oxygen not only suppressed the deposition rate but also increased the electron density of the film, resulting in better crystallinity. Hence, the presence of oxygen during deposition should be considered as one of the essential parameters for improving the structural and magnetic properties of ferrite films.     

基于涡动相关法的沉积物-水界面氧通量与水动力条件响应关系

沉积物-水界面是物质参与环境地球化学循环和生物耦合的"热区",水动力条件是沉积物-水界面物质交换的关键影响因素。溶解氧作为常用的水质评价指标,对调节生物化学进程有重要作用,因此本文采用涡动相关法这种非侵入式通量测量技术开展室内试验研究,探究沉积物-水界面氧通量与水动力条件的响应关系。结果表明:随着水体紊动增加(采用Batchelor尺度表征),扩散边界层厚度减小,氧通量增大。分析室内试验和相关研究中水动力条件、扩散边界层厚度及氧通量的关系,发现扩散边界层厚度与Batchelor尺度呈正相关关系,拟合结果表明可以用Batchelor尺度近似表示扩散边界层厚度;氧通量与扩散边界层厚度呈负相关关系,且当扩散边界层厚度小于0.5 mm时,扩散边界层厚度变化对氧通量影响更强烈,当厚度大于0.5 mm后,氧通量基本保持稳定。     

白藜芦醇丙烯酸酯的合成及抗氧化活性研究

以白藜芦醇为先导化合物,合成了白藜芦醇丙烯酸酯,以获得具有更好抗氧化活性的白藜芦醇衍生物。以白藜芦醇和丙烯酰氯为原料,酯化法得到白藜芦醇丙烯酸酯。以维生素C为阳性对照,研究白藜芦醇丙烯酸酯对2,2-联苯-1-苯基肼(DPPH)自由基的清除活性和抗氧化活性。用NMR和HRLC-MS对白藜芦醇丙烯酸酯进行了表征。目标产物白藜芦醇丙烯酸酯收率为30.2%。白藜芦醇丙烯酸酯的抗氧化活性高于白藜芦醇,但低于维生素C。合成得到了白藜芦醇丙烯酸酯,其反应路线简单易行,条件温和,产物抗氧化活性较先导化合物有所提高。     

氧化石墨烯改性碳纤维复合材料抗冲击行为研究

使用单层纳米氧化石墨烯（NGO）粒子对环氧树脂进行改性处理，采用真空辅助树脂传递模塑成型工艺制备了[±45/0/90]_2S铺层角度下的纯树脂及单层NGO改性碳纤维复合材料（CFRP）层合板。通过落锤冲击试验、超声C扫描检测、冲击后压缩试验等对纯树脂及单层NGO改性CFRP进行实验研究。结果表明，纯树脂及单层NGO改性CFRP在损伤阻抗及损伤容限实验中均存在拐点现象，且拐点出现在相同深度位置，其中纯树脂CFRP拐点位置为0.51 mm，单层NGO改性CFRP拐点位置为0.43 mm；相对于纯树脂CFRP，单层NGO改性CFRP可以显著提高复合材料的抗冲击性能及冲击后的压缩性能；通过对冲击后凹坑深度及凹坑面积进行数据模拟，可以用拟合公式实现对复合材料的损伤预测。     

工艺参数对6061-T6铝合金真空扩散焊接接头形貌和性能的影响

在不同工艺参数下对化学清洗去除表面氧化膜的6061-T6铝合金进行真空扩散焊接,研究了焊接温度(500~560℃)、焊接压力(1.0~5.0MPa)和保温时间(0.5~3h)对焊接接头界面形貌和剪切强度的影响,得到了优化工艺参数。结果表明:随着焊接温度的升高、焊接压力的增大和保温时间的延长,接头焊缝变窄并最终消失,剪切强度和焊合率增大;但当保温时间延长到3h时,焊缝附近晶粒发生粗化,导致剪切强度降低,且接头发生较大变形;不同工艺参数下接头的剪切断裂形式均为脆性断裂;较优的真空扩散焊接工艺参数为焊接温度540℃、保温时间2h、焊接压力4.0MPa。     

改性纳米碳酸钙用于硅酮胶挤出性研究

采用碳化法合成纳米碳酸钙,在反应过程中,调整反应起始温度合成不同晶型大小的纳米碳酸钙。通过透射电镜（TEM）、激光粒度仪对碳酸钙的物相、形貌、粒度进行分析,将改性纳米碳酸钙应用于硅酮胶基料制备及挤出性研究,分析改性纳米碳酸钙的颗粒大小、分散性、流变性能及表面改性剂对挤出性的影响。结果表明：粒径介于50~90 nm,屈服值介于66.4~148.9 Pa,黏度介于0.5~0.75 mPa·s,硬脂酸钠与LH-2、LH-3两种包覆剂进行复配改性的纳米碳酸钙用于硅酮胶基料具有较好的挤出性能。